Nissan Rogue Service Manual: P2813 select solenoid

Nissan Rogue Service Manual / Transmission & driveline / Transaxle & Transmission / Dtc/circuit diagnosis / P2813 select solenoid

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms (Trouble diagnosis content)

DTC detection condition

P2813

SELECT SOLENOID (Select solenoid)

When any of 1, or 2 is satisfied:

When all the following conditions are established three times in 1DC

Precondition

DTC other than the applicable DTC is not detected.
Throttle position: More than 6.27 deg.
Vehicle speed: Less than 3 km/h (1 MPH)
CVT fluid temperature: More than 20°C (68°F)
Selector lever: Other than P, N
Turbine speed when performed N → D, N (P) → R: More than 500 rpm
TCM power supply voltage: More than 11 V

Detection time

N → D: 0.4 seconds
N → R: 0.3 seconds
P → R: 0.3 seconds

When all of the following conditions are satisfied and this state is maintained for 30 seconds:

The counting of time continues while all of the following conditions are satisfied and stops when the conditions become unsatisfied (the count is maintained). When accumulated time reaches 30 seconds (Clutch is judged as engaged and the count is reset.)

Selector lever: Other than P, N
Vehicle speed: Less than 3 km/h (1 MPH)
Differences between primary pulley speed and secondary speed: Less than 120 rpm
Clutch instructions pressure: 0.95 MPa or more
Differences between turbine speed and input speed: Less than 200 rpm
Turbine speed – speed: More than 450 rpm
DTC other than the applicable DTC is not detected.
TCM power supply voltage: More than 11 V

NOTE: DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF → ON → driving → OFF”.

POSSIBLE CAUSE

Select solenoid valve

FAIL-SAFE

When a malfunction occurs on the low oil pressure side

Selector shock is large
Start is slow
Acceleration is slow
Vehicle speed is not increased

When a malfunction occurs on the high oil pressure side

Selector shock is large

DTC CONFIRMATION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION 1

Start the engine.
Maintain the following conditions. (Keep 30seconds or more after the selector lever shifted.)

Selector lever : N→ D, N → R, P→ R

Check the first trip DTC.

Is “P2813”detected? YES >> Go to TM-171, "Diagnosis Procedure".

NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

1.REPLACE TRANSAXLE ASSEMBLY

Replace transaxle assembly. Refer to TM-220, "Removal and Installation".

>>WORK END

P2765 input speed sensor B

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2765 INPUT SPEED SENSOR B (Input/Turbine Speed Sensor ...

P2814 select solenoid

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2814 SELECT SOLENOID (Select solenoid) When all of ...

Other materials:

Accelerator pedal released position learning
Description Accelerator Pedal Released Position Learning is a function of ECM to learn the fully released position of the accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time harness connector of accelerator pedal position sensor ...

Door sash molding
Exploded View Front door sash molding Rear door rear sash molding Front door panel Rear door panel Roof rail side outer Body side outer Rear door weather strip Rear door glass Removal and Installation FRONT DOOR Removal Remove door mirror. Refer to MIR-22, &q ...

P2815 select solenoid
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2815 SELECT SOLENOID (Select solenoid) When all of the following conditions are satisfied and this state is maintained for 0.2 seconds: &nb ...