Nissan Rogue manuals

Nissan Rogue Service Manual: Oil pan and oil strainer

Exploded View

Exploded View

  1. Oil pan, upper
  2.  Oil filter
  3.  Front cover
  4.  O-ring
  5.  Oil strainer
  6.  Oil pan, lower
  7.  Washer
  8. Drain plug
  9. O-ring
  10.  Oil level gauge guide
  11. Oil level gauge
  12.  Rear cover plate
  1.  To Oil pan, lower

Removal and Installation

REMOVAL

WARNING: To avoid danger of being scalded, do not drain engine oil when engine is hot.

  1.  Drain engine oil. Refer to LU-8, "Draining".
  2.  Remove the oil filter. Refer to LU-10, "Removal and Installation".
  3. Remove fender protector (RH). Refer to EXT-28, "FENDER PROTECTOR : Removal and Installation".
  4.  Remove the front driveshaft (RH). Refer to FAX-20, "Removal and Installation (RH)".
  5.  Remove the front exhaust tube and gaskets. Refer to EX-5, "Exploded View".
  6.  Remove bolt (A) securing oil level gauge (2).
  7.  Remove oil level gauge (1), oil level gauge guide (2), and O-ring (3).

Removal and Installation

  1. Remove the power steering gear bolts and support the power steering gear. Refer to ST-14, "Removal and Installation".
  2.  Remove the rear engine mount torque rod bracket. Refer to EM-81, "Exploded View".
  3. . Remove the front suspension member for clearance to remove the oil pan. Refer to FSU-20, "Removal and Installation".
  4.  On models equipped with AWD, remove transfer assembly. Refer to DLN-70, "Removal and Installation".
  5.  Disconnect the A/C compressor harness connector.
  6.  Remove the A/C compressor bolts, position the A/C compressor aside and support. Refer to HA-30, "Removal and Installation".
  7.  Remove the lower oil pan bolts in the reverse order as shown.

Removal and Installation

  1. Remove the lower oil pan using Tool (A).

    CAUTION: Be careful not to damage the mating surfaces.

    NOTE: In areas where the cutter is difficult to use, use a plastic hammer to lightly tap (1) the cutter where the liquid gasket is applied. Use a plastic hammer to slide (2) the cutter by tapping on the side.

Tool number : KV10111100 (J-37228)

Removal and Installation

  1. Remove the oil strainer bolts in the reverse order as shown then remove the oil strainer.

Removal and Installation

  1. Remove rear cover plate and engine-to transaxle bolts.
  2.  Loosen the upper oil pan bolts in the order shown.

Removal and Installation

  1. Remove upper oil pan using Tool (A).

Tool number : KV10111100 (J-37228)

Removal and Installation

INSPECTION AFTER REMOVAL

Clean the oil strainer screen to remove any foreign material.

INSTALLATION

  1.  Apply Genuine Silicone RTV Sealant or equivalent to the upper oil pan at the specified sealant bead diameter (A) as shown.

    Refer to GI-22, "Recommended Chemical Products and Sealants".

Sealant bead diameter (A) : 4.0 - 5.0 mm (0.157 - 0.197 in)

Installation

CAUTION:

  1. Install the upper oil pan to the block and tighten the upper oil pan bolts to specification in the order shown.

    CAUTION: Install upper oil pan bolts in the same position from which they were removed.

All bolts except 18 and 19 : 21.6 N·m (2.2 kg-m, 16 ft-lb)
Bolts 18 and 19 : 8.8 N·m (0.90 kg-m, 78 in-lb)

Installation

  1. Apply Genuine Silicone RTV Sealant or equivalent to the lower oil pan at the specified sealant bead diameter (A) as shown.

    Refer to GI-22, "Recommended Chemical Products and Sealants".

CAUTION:

Sealant bead diameter (A) : 4.0 - 5.0 mm (0.157 - 0.197 in)

Installation

  1.  Install the lower oil pan to the upper oil pan and tighten the lower oil pan bolts to specification in the numerical order shown.

Installation

  1. Install oil level gauge (1), oil level gauge guide (2), and O-ring (3).

Bolt (A) : 21.6 N·m (2.2 kg-m, 16 ft-lb)

Installation

  1. Installation of the remaining components is in the reverse order of removal.

INSPECTION AFTER INSTALLATION

Check for engine oil leaks with the engine at operating temperature and running at idle. Refer to LU-7, "Inspection".

Exhaust manifold and three way catalyst
Exploded View Cylinder head Exhaust manifold and three way catalyst gasket  Exhaust manifold cover (upper)  Exhaust manifold and three way catalyst  Exhaust manifold ...

Ignition coil
Exploded View Ignition coil  Spark plug Rocker cover Removal and Installation REMOVAL  Remove air duct assembly. Refer to EM-24, "Exploded View" .  Dis ...

Other materials:

Liftgate
WARNING  Always be sure the liftgate has been closed securely to prevent it from opening while driving.  Do not drive with the liftgate open. This could allow dangerous exhaust gases to be drawn into the vehicle. Refer to “Exhaust gas (carbon monoxide)â ...

Component parts
Component Parts Location Rear luggage area (RH) Front headliner area Engine compartment (LH)  Left side of instrument panel (view with finish panel removed)  Instrument panel (LH) No. Part Description 1 Back door lock assembly (ba ...

Power window motor
DRIVER SIDE DRIVER SIDE : Description Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch. DRIVER SIDE : Component Function Check 1. CHECK FRONT POWER WINDOW MOTOR LH OPERATION Check front power window motor LH operation with main power window a ...

© 2014-2023 Copyright www.nirogue.com