Nissan Rogue Service Manual: Excessive operation frequency
Description
VDC function, TCS function, ABS function, EBD function, Brake limited slip differential (BLSD) function, Brake assist function, hill start assist function or Brake force distribution function operates in excessive operation frequency.
Diagnosis Procedure
1.CHECK BRAKING FORCE
Check brake force using a brake tester.
Is the inspection result normal? YES >> GO TO 2.
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Check that there is no excessive looseness in front and rear axle.
- 2WD: Refer to FAX-7, "Inspection" (front) or RAX-6, "Inspection" (rear).
- AWD: Refer to FAX-38, "Inspection" (front) or RAX-14, "Inspection" (rear).
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK WHEEL SENSOR
Check wheel sensor.
- Check installation and damage of wheel sensor.
- Check connection of wheel sensor harness connector.
- Check terminal of wheel sensor harness connector.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair installation or replace wheel sensor.
- Front wheel sensor: Refer to BRC-132, "FRONT WHEEL SENSOR : Removal and Installation".
- Rear wheel sensor: Refer to BRC-134, "REAR WHEEL SENSOR : Removal and Installation".
4.CHECK SENSOR ROTOR
Check that there is no looseness, damage or foreign material on sensor rotor.
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair installation or replace sensor rotor.
- Front sensor rotor: Refer to BRC-135, "FRONT SENSOR ROTOR : Removal and Installation - Front Sensor Rotor".
- Rear sensor rotor: Refer to BRC-135, "REAR SENSOR ROTOR : Removal and Installation - Rear Sensor Rotor".
5.CHECK WARNING LAMP TURNS OFF
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn OFF approx. 1 second after key switch is turned ON and stay in OFF status during driving.
CAUTION: Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake fluid is less than the specified level (brake fluid level switch is ON). Is the inspection result normal? YES >> Normal NO >> GO TO 6.
6.PERFORM THE SELF-DIAGNOSIS
With CONSULT
- Turn the ignition switch OFF → ON.
CAUTION:
- Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
- Set the vehicle to READY/Start the engine.
- Repeat step 1 two or more times.
- Perform self-diagnosis for “ABS”.
Is any DTC detected? YES >> Check the DTC. Refer to BRC-55, "DTC Index".
NO >> Inspection End.
Unexpected brake pedal reaction
Description
A malfunction of brake pedal feel (height or others) is detected when brake
pedal is depressed.
Diagnosis Procedure
1.CHECK FRONT AND REAR AXLE
Check that there is no excessive loose ...
Other materials:
The parking brake release warning continues sounding, or
does not sound
Description
The parking brake warning buzzer sounds continuously during vehicle
travel though the parking brake is
released.
The parking brake warning buzzer does not sound at all even though
driving the vehicle with the parking
brake applied.
Diagnosis Procedure
1. CHECK P ...
Primary speed sensor
Exploded View
Transaxle assembly
O-ring
Primary speed sensor
: Always replace after every
disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
Removal and Installation
REMOVAL
Remove the engine undercover. Refer to EXT-37, "ENGINE UNDER COVER
: Removal and Ins ...
P0705 transmission range sensor A
DTC Description
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0705
T/M RANGE SENSOR A
[Transmission Range Sensor A Circuit (PRNDL
Input)]
When all of the following conditions are satisfied and this state is
...
