Nissan Rogue Service Manual: C1105, C1106, C1107, C1108 wheel sensor

Nissan Rogue Service Manual / Brakes / Brake Control System / DTC/circuit diagnosis / C1105, C1106, C1107, C1108 wheel sensor

DTC Logic

DTC DETECTION LOGIC

DTC	Display Item	Malfunction detected condition	Possible causes
C1105	RR RH SENSOR-2	When distance between rear wheel sensor RH and rear wheel sensor RH rotor is large. When installation of rear wheel sensor RH or rear wheel sensor RH rotor is not normal.	Wheel sensor ABS actuator and electric unit (control unit) Sensor rotor
C1106	RR LH SENSOR-2	When distance between rear wheel sensor LH and rear wheel sensor LH rotor is large. When installation of rear wheel sensor LH or rear wheel sensor LH rotor is not normal.
C1107	FR RH SENSOR-2	When distance between front wheel sensor RH and front wheel sensor RH rotor is large. When installation of front wheel sensor RH or front wheel sensor RH rotor is not normal.
C1108	FR LH SENSOR-2	When distance between front wheel sensor LH and front wheel sensor LH rotor is large. When installation of front wheel sensor LH or front wheel sensor LH rotor is not normal.

DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAGNOSTIC RESULT

With CONSULT.

Start engine and drive vehicle at approximately 21 km/h (13 MPH) or more for approximately 5 minutes.
Perform self-diagnostic result.

Is DTC C1105, C1106, C1107 or C1108 detected? YES >> Proceed to diagnosis procedure. Refer to BRC-78, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Regarding Wiring Diagram information, refer to BRC-57, "Wiring Diagram".

1.CONFIRM DTC

With CONSULT

Perform self-diagnostic result of “ABS” and record all active DTCs.
Clear all DTCs.
Perform DTC confirmation procedure. Refer to BRC-74, "DTC Logic".

Does DTC C1105, C1106, C1107 or C1108 reset? YES >> GO TO 2.

NO >> Refer to GI-41, "Intermittent Incident".

2.CHECK TIRE PRESSURE AND TIRE WEAR

Check tires for excessive wear and proper inflation. Refer to WT-57, "Adjustment".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace as necessary.

3.CHECK WHEEL SENSOR

Check wheel sensor for the following:

Proper installation
Physical damage
Contamination

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace as necessary.

4.CHECK SENSOR ROTOR

Check sensor rotor for the following:

Contamination
Physical damage (missing teeth, cracks, etc.)
Foreign material
Looseness

Is the inspection result normal? YES >> Replace the wheel sensor. Refer to BRC-132, "FRONT WHEEL SENSOR : Removal and Installation" or BRC-134, "REAR WHEEL SENSOR : Removal and Installation". Then, GO TO 5.

NO >> Repair or replace as necessary.

5.CONFIRM REPAIR

With CONSULT

Clear all DTCs.
Perform DTC confirmation procedure. Refer to BRC-78, "DTC Logic".

Does DTC C1105, C1106, C1107 or C1108 reset? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".

NO >> Inspection End.

C1101, C1102, C1103, C1104 wheel sensor

DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1101 RR RH SENSOR-1 When power supply voltage of rear wheel sen ...

C1109 power and ground system

DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1109 BATTERY VOLTAGE [ABNORMAL] When ignition voltage is 10 ...

Other materials:

Rear bumper
Exploded View Rear bumper fascia side bracket (LH) Rear mud protector Rear bumper reinforcement support (LH) Rear bumper fascia undercover (LH) Rear bumper reinforcement Rear energy absorber Rear bumper bracket (LH) Rear bumper fascia Rear bumper fascia re ...

EPS warning lamp does not turn off
Description EPS warning lamp does not turn OFF several seconds after engine started. Diagnosis Procedure 1.PERFORM SELF-DIAGNOSIS With CONSULT Turn the ignition switch OFF to ON. Perform “EPS” self-diagnosis. Is any DTC detected? YES >> Check the DTC. Refer to STC ...

Power outlets
Instrument Panel 12V OUTLETS The power outlets are for powering electrical accessories such as cellular telephones. They are rated at 12 volt, 120W (10A) maximum. The front and center console power outlets are powered only when the ignition switch is in the ACC (if so equipped) or ON po ...