Nissan Rogue Service Manual: Brake warning lamp
Component Function Check
1.CHECK BRAKE WARNING LAMP FUNCTION
Check that brake warning lamp in combination meter turns ON for 1 second after ignition switch is turned ON.
CAUTION: Never start the engine. Is the inspection result normal? YES >> GO TO 2.
NO >> Proceed to BRC-120, "Diagnosis Procedure".
2.CHECK BRAKE WARNING LAMP FUNCTION
Check that brake warning lamp turns ON/OFF when parking brake is operated.
NOTE: Brake warning lamp turns ON when parking brake is operated (when parking brake switch is ON). Is the inspection result normal? YES >> GO TO 3.
NO >> Check the parking brake switch system. Refer to BRC-115, "Diagnosis Procedure".
3.CHECK BRAKE WARNING LAMP FUNCTION
Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated while brake fluid level in reservoir tank is with the specified level.
NOTE: Brake warning lamp turns ON when brake fluid is less than the specified level (when brake fluid level switch is ON). Is the inspection result normal? YES >> Inspection End.
NO >> Check the brake fluid level switch system. Refer to BR-27, "Exploded View".
Diagnosis Procedure
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
Refer to BRC-120, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.PERFORM THE SELF-DIAGNOSIS
With CONSULT
- Turn the ignition switch OFF → ON.
CAUTION:
- Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
- Start the engine.
- Repeat step 1 two or more times.
- Perform self-diagnosis for “ABS”.
Is any DTC detected? YES >> Check the DTC. Refer to BRC-55, "DTC Index".
NO >> GO TO 3.
3.CHECK BRAKE WARNING LAMP SIGNAL
With CONSULT
- Select “ABS”, “DATA MONITOR” and “EBD WARN LAMP” according to this order.
- Turn the ignition switch OFF.
- Check that data monitor displays “On” for 1 second after ignition switch is turned ON and then changes to “Off”.
CAUTION: Never start the engine. Is the inspection result normal? YES >> Replace the combination meter. Refer to MWI-82, "Removal and Installation".
NO >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".
ABC warning lamp
Component Function Check
1.CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combination meter turns ON for 1 second after
ignition switch is turned ON.
CAUTION:
Never start the eng ...
VDC warning lamp
Component Function Check
1.CHECK VDC WARNING LAMP FUNCTION
Check that VDC warning lamp in combination meter turns ON for 1 second after
ignition switch is turned ON.
CAUTION:
Never start the e ...
Other materials:
P0863 TCM communication
DTC Description
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0863
CONTROL UNIT (CAN)
(TCM Communication Circuit)
An error is detected at the initial CAN diagnosis of TCM.
POSSIBLE CAUSE
TCM
FAIL-SAFE
...
Diagnosis and repair work flow
Work Flow
OVERALL SEQUENCE
DETAILED FLOW
1.INTERVIEW THE CUSTOMER FOR THE SYMPTOM
Interview the customer for the symptom (the condition and the environment
when the incident/malfunction
occurs).
>> GO TO 2.
2.CHECK SYMPTOM
Check the symptom from the customer information.
> ...
Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT
PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
...
